Research Topic

Strut

8 Publications Matching this Keyword

Impact Factor
7.883
Strut

8 Matching Papers


All Categories
Publish Your Paper

Submit your research manuscript for fast peer review and publication.

Submit Paper

Papers tagged with "Strut"

Showing page 1 of 1
Vol 10, Issue 2 (February 2024) Civil Engineering

A REVIEW ON ANALYSIS OF A DEEP BEAM STRUCTURE WITH DIFFERENT BEAM USING ANALYSIS TOOL

Deep Beams Generally Face Failure Due To Shear Force Due To Being Brittle In Nature Leading To Catastrophic Consequences. Such Phenomenon Creates A Necessity To Investigate Shear Deficiency Generated Under Deep Beams When Subjected To Later...

Girijashankar Patel, Hitesh Kodwani
Vol 5, Issue 10 (October 2019) Civil Engineering

SEISMIC PERFORMANCE EVALUATION OF RC FRAME BUILDING WITH INFILL WALLS

Masonry Infill Walls, Which Generally Have High Stiffness And Strength, Significantly Affect The Seismic Response Of Reinforced Concrete Frame Buildings. Before The Introduction Of IS 1893 (Part I)-2016 Practice Of Structural Design In Indi...

Sheetal Devhare, S. N. Daule
Vol 5, Issue 6 (June 2019) Mechanical Engineering

CRITICAL ANALYSIS OF FILAMENT WOUND STRUTS UNDER COMPRESSION LOADING WITH ONE END FIXED OTHER END FREE CONDITION

Specific Strength And Stiffness Ratios Are Important Structural Design Parameters In Aerospace And Automotive Industries.This Development Is Motivated By The Demand For Corrosion Resistant, Lighter And And High Specific Stiffness Components...

Ms. K.Vijaya Sree, Msb.Charitha, Mr.Adesh Bhil, Mr.B Harishraj
Vol 5, Issue 2 (February 2019) Civil Engineering

COMPARATIVE ANALYSIS OF L-SHAPED RC FRAME BY REPLACING MASONRY FROM STRUT USING RESPONSE SPECTRUM ANALYSIS

Infill Panels Are Widely Used As Partition Walls As Well As External Walls Of The Building To Fill The Gap Between RC Frames. Non-structural Member May Provide Considerable Stiffness To The Building And Hence May Improve The Performance Of...

Vishal P, Rajeeva S V
Vol 3, Issue 9 (September 2017) Mechanical Engineering

STATIC STRUCTURALS ANALYSIS & OPTIMIZATION OF AUTOMOTIVE A-ARM

The Suspension Control Arm Is An Intermediary With The Suspension System, Has A Major Function To Cope With. The Wheel Base On One End And The Connection To The Chassis Member Exposes The Part To High Stresses While Performing Its Function...

Kishor Gheware, Prof. K.H. Munde, Prof. G.E.Kondhalkar
Vol 3, Issue 7 (July 2017) Civil Engineering

FINITE ELEMENT ANALYSIS OF IN-FILL PANELS IN RCC FRAME FOR SEISMIC ZONE III USING STAAD

The Presence Of Infill Wall In The Building Gives Better Behavior Under Lateral Loads. For Multistoried Structures, The Consideration Of Effect Of Bottom Storey Under Seismic Forces Would Be An Important Parameter. As Per IS 1893 (Part-I) :...

Miss Sujata Barde
Vol 3, Issue 4 (April 2017) Structural Engineering

Study on Flexural Behavior of Corbel Wrapped With FRP Sheet

The Non Prismatic And Non Linear Members Like Deep Beams, Dapped Ended Beam And Corbels Etc.are Not Satisfied With Normal Beam Theory. These Structures Generally Fail By Shear In Spite Of Flexure And Could Not Be Possible To Analyses And De...

Mr. Bande.Vidhyasagar N, Prof. Bhusare Vijaykumar
Vol 2, Issue 3 (March 2016) Mechanical Engineering

ANALYSIS OF A SPRING LOADED INTERCONNECTED HYDRO-PNEUMATIC SUSPENSION OF A VEHICLE

In 1950, Hydro-pneumatic Suspensions Were Used In Vehicle To Increase The Ride Comfort Due To Nonlinear Property Of Oil And Air. But Due To The Sizes Of Struts Unreasonably Large Further, The Pressures Were Also Unreasonably High Resulti...

Dhage A. C., Sawant N. B., Bansode S. N., Shaligram A. A., Mohite M. A.

Submit Your Paper to IJSART

Join the global research community with IJSART. Submit your paper, share your work, and gain worldwide recognition!